How do you reset a Fellowes paper shredder?
b) The shredder may need to be reset. Switch it to the reverse (R) position for 2 seconds and then back to auto (I). This should reset it and it will operate again.
How do you reset a Fellowes shredder?
Empty the wastebasket and move the power switch to the Reverse position if the shredder jams. This should reverse the jammed paper out of the shredder. Toggle the switch between Reverse and Auto if the shredder jams again. Pull the paper out manually if the switch-toggling fails to clear the jam.
Why has my Fellowes shredder stopped working?
Too much paper or too many credit cards could have been put into the shredder at once. Try reversing the wheel rotation using the on, off, and reverse switch located on top of the shredder. If that is unsuccessful remove the obstruction from the shredding wheels and try again.
What does the red light mean on my Fellowes shredder?
Yes, the RED LIGHT comes on when you separate the SHREDDING HEAD from the bucket. When you put the SHREDDING HEAD back into place after emptying the bucket, the RED LIGHT goes off. If you shredder is not shredding, is there a chance that you have overheated the unit.
What to do if shredder stops working?
Dust-free paper shredder blades. Turn on your paper shredder again and check if the paper shredder is unjammed. If it is, also lubricate the paper shredder blades to make sure the cutting blades run smoothly.
Can you repair a Fellowes shredder?
Fellowes office/commercial shredders (large shredders that cannot fit under a desk) are repairable and parts will most likely be available. Please do not try to repair the shredder yourself or you will void your warranty.
What does the yellow light mean on a Fellowes shredder?
The yellow sensor light should turn on, indicating that the SafeSense® feature is working. If the SafeSense® light is flashing continuously, this indicates that the SafeSense® feature is in the override position.
Where is the sensor on a Fellowes shredder?
A majority of Fellowes shredders have 2 small electronic sensors in the throat of the paper entry slot.
How do you manually clean a Fellowes shredder?
Turn the shredder on, feed a shredder oil sheet through, wait for it to shred completely through, feed through a few sheets of plain paper to absorb the excess oil, turn off the shredder, apply lubricating oil to the top of the blades, switch shredder on in reverse to evenly distribute oil, feed through some paper to …
How do you unclog a Fellowes shredder?
If your shredder is jammed, press the “reverse” button for two seconds. As the shredder reverses the paper, gently pull out the uncut portion. If reversing the paper does not unclog the jam, try toggling between “reverse” and “auto forward” for two seconds each. This will help to clear the paper from the blades.
How do you Unjamm a paper shredder?
Switch the shredder to “reverse” and plug it back in.
Because jamming is a common problem, most modern shredders come with a built-in option to run in reverse. Switch the shredder to its “reverse” option (usually there is a well-marked button on the top of the shredder) before plugging it back in.
How do you clean shredder blades?
Clean the shredder blades
Once a month, or after a major shredding project (such as at the end of a retention schedule), clear out the blades. After removing the remnant bits of paper, use a can of compressed air to clean out the dust and smallest pieces stuck in the blades.
Why does my paper shredder only work in reverse?
The shredder will only constantly run in the “Reverse” mode. The trigger located in the center of the feed entry slot, which activates the shredder, may be blocked. To clear it, you would need to insert an index card or file folder (i.e. rigid paper or cardstock) in the center of the feed slot and apply force.
Where is the reverse button on Fellowes shredder?
The shredder should have a clearly marked “reverse” button or control switch depending on the machine. This is typically located on the top of the shredder.